|
Microchip公司的數字純正弦波的離線1000W不間斷電源( UPS)參考設計采用dsPIC33FJ16GS系16位數字信號控制器(DSC),輸入交流電壓210 – 242V, 50 Hz (+/- 3 Hz),輸出交流電壓220V @ 50 Hz (+/ - 1 Hz),額定功率1000VA,效率84%,純正弦波輸出THD小于3%,火線到電池轉換時間小于10ms,可用作計算機和通信設備的保護電源.本文介紹了UPS參考設計主要指標,采用dsPIC33FJ16GS504的離線UPS方框圖,電路圖,材料清單和PCB元件布局圖. Digital Pure Sine Wave Uninterruptible Power Supply (UPS) Reference Design dsPIC33FJ06GS101/X02 and dsPIC33FJ16GSX02/X04 Data Sheet High-Performance, 16-bit Digital Signal Controllers 
圖1.正弦波UPS參考設計外形圖 UPS參考設計輸入/輸出指標: Input / Output Specifications: Input Range AC: 95 – 135V, 60 Hz (+/ - 3 Hz) (110V version) 210 – 242V, 50 Hz (+/- 3 Hz) (220V version) Output Voltage AC: 110V @ 60 Hz (+/ - 1 Hz) (110V version) 220V @ 50 Hz (+/ - 1 Hz) ( 220V version) DC Input: 36V (12 VDC X 3) Lead Acid Battery Rating: 1000 VA Steady-State Output Power 1350 VA Peak Power (Surge) Features: High-frequency design Adjustable Charging current Efficiency of 84% Pure sine wave output with THD <3% Mains to Battery Transfer time < 10 ms Supports Crest Factor of 3:1 Minimum Power Factor(Leading/Lagging) of 0.65 Fault indications USB Communication with PC LCD front panel An Uninterruptible Power Supply, or UPS, is an electronic device that provides an alternative electric power supply to connected electronic equipment when the primary power source is not available. Unlike auxiliary power, a UPS can provide instant power to connected equipment, which can protect sensitive electronic devices by allowing them to shut down properly and preventing extensive physical damage. However, a UPS can only supply energy for a limited amount of time, typically 15 to 20 minutes. Although its use can extend to a virtually unlimited list of applications, in past years the UPS has become even more popular as a means of protecting computers and telecommunication equipment, thus preventing serious hardware damage and data loss. Types of UPS Systems A typical UPS for computers has four basic protection roles: being able to cope with power surges, voltage shortage, complete power failure and wide variations in the electric current frequency. There are three types of UPS systems, depending on how the electric power is being stored and relayed to the electronic device connected to them: • Offline UPS (also known as Stand-by UPS) • Line-Interactive (or Continuous UPS) • Online UPS (often called double conversion supply)
圖2.離線UPS方框圖
圖3.采用dsPIC33FJ16GS504的離線UPS方框圖 The reference design in this application note describes the design of an Offline Uninterruptible Power Supply (UPS) using a Switch Mode Power Supply (SMPS) dsPIC® Digital Signal Controller (DSC). The Offline UPS Reference Design consists of three major UPS topology blocks: • Push-Pull Converter (steps up the DC battery voltage to a constant high-voltage DC) • Full-Bridge Inverter (converts DC voltage to a sinusoidal AC output) • Flyback Switch Mode Charger (current source and charges battery with constant current) 1kW離線UPS主要指標:
圖4.離線UPS參考設計框圖
圖5.開關模式充電器框圖
圖6.離線UPS詳細框圖
圖7.離線UPS參考設計電路圖(1)
圖8.離線UPS參考設計電路圖(2)
圖9.離線UPS參考設計電路圖(2)
圖10.離線UPS參考設計電路圖(3)
圖11.離線UPS參考設計電路圖(4)
圖12.離線UPS參考設計電路圖(5)
圖13.離線UPS參考設計電路圖(6)
圖14.離線UPS參考設計電路圖(7)
圖15.離線UPS參考設計PCB布局圖(頂層) 離線UPS參考設計材料清單見:
離線UPS參考設計材料清單.pdf
(156.75 KB)
詳情請見:
70318D[1].pdf
(5.01 MB)
01279B[1].pdf
(1.96 MB)
|
